|
Product ReleaseSelecting Keyless vs Keyed Connections for Motor to Gear Reducer
Knowing the differences between keyless and keyed-shafted connections is vital in distinguishing the advantages and disadvantages of both types of specifications when choosing a gearbox for your motor. In today’s marketplace, the need for speed, precision and small size are not only dictating the standard for shaft locking devices but also challenging motion component manufacturers to evaluate methods of keyless shaft locking for dynamic loads. Motor and drive manufacturers are making products in smaller and smaller packages which are increasingly capable of rapid acceleration and rotary positioning accuracy. These industry changes are causing backlash, stress distribution and balance to all be addressed in shaft locking devises, in many cases rending the shaft key obsolete. In the examples that follow, both types of connections are compared in terms of torque transmission. A shaft with a diameter of 16mm is used for both cases. The key and keyway dimensions are standard according to DIN 6885. Calculations show the maximum torque that can be transmitted through both keyed and keyless shafts. Also, there are calculations for maximum transmissible torque for the key only. Material for the shaft and key is steel 35S20. I. Keyless shaft With the assumption that slipping will not occur, the torque transmitted through the shaft is:  This is the maximum torque that can be transmitted through the keyless shaft before any plastic deformations take a place. II. Keyed shaft The stress level imposed on the keyway sides is critical in evaluating keyed applications. With the assumption that the key will not fail before the shaft, torque which the shaft can hold is:  The value 228Nm is the maximum torque that can be transmitted through the keyed shaft with diameter of 16mm before any plastic deformations occur. III. Key The most commonly used type of key is the flat key. With this type, there are two modes of failure likely: shear failure and crushing failure. In the calculations the total value of the yield stress is used and the factor of safety is not included. Shear failure of the flat keys The keyway of the shaft and hub exert equally and opposite forces on the key, resulting in shear deformation. This equates to the forces attempting to shear the key at the radius of the shaft. Shear stress can be noted as follows:  Crashing failure of the shaft keys Contact of the keyways in the shaft and the hub can result in permanent compressive deformation. This crushing stress is a result of compressive stress that equals the applied force divided by the area of contact.  The key’s torque handling capacity is 190N.m. This equates to the torque that the key can hold before plastic deformation. Another factor to consider is having the optimal fit when mating the key to the keyway. According to ISO JS9 for parallel key with normal fit, the tolerance for the keyway with a width of 5mm is +0.015 /– 0.015mm. The key’s tolerance per DIN 6885 is +0.05/0. The clearance between the shaft’s keyway and the key is up to 0.015mm, allowing angular movement of the shaft up to 0.1074°. This relates to a 6.445 arcminutes potential backlash. In addition, the keyway tolerances allow for keyways that may be 0.015mm off the shaft centerline. Calculations: The assumption in this case is that the key slides instead of twisting.  If it is assumed that the key is in the middle and twists, the backlash is as follows:  The most vital aspect when addressing performance issues is the concern with backlash. Fully eliminating backlash is rarely possible; however, backlash can be reduced by precise fitting of the gearbox to motor and complicated machining. The increase in keyway wear is due to a variety of factors. Increased quantity of frequent machine starts, stops and load reversals are some common causes of key wear. With increasing acceleration and deceleration rates, wear is increased in terms of both the frequency and force of the impact between the key and keyway. As time passes, backlash will also increase at an accelerated rate. Resulting from impact, material is compressed and removed from the keyway, widening the keyway and making the velocity at which the key impacts the keyway higher with each load change. Highly dynamic loading can result in keyways wearing down to the point of problematic backlash or even failure over a very short time span. More over, having a keyway may pose problematic at the time of disassembly. Depending on the environment and duty cycle, oxidation and corrosion may occur and, as a result, can “weld” the key assembly components. Eliminating the problems stated above requires eliminating the keyway method and using a frictional type of connection between the components of the assembly, one sample of which can be using a shrink disk. Shrink disk connection will result in a zero clearance and consequently no additional backlash on the system. Also, it leads to higher amount of transmissible torque according to the calculations above. Finally, eliminating the keyway doesn’t require consideration of keyed shaft notch factors. That allows a smaller shaft diameter and smaller bearing sizes which leads to decreasing overall the cost of the system. |
Print
Ternary is an all-in-one linear system that merges mechanics with intelligence, integrating several separate components: electronics, precision mechanics, feedback, control and software. Ternary is ideal in all situations where a pneumatic cylinder isn’t enough and a servo is too expensive and too complicated. alpha’s linear system allows multiple positions to be controlled with utmost precision, yet costs very little. Compactness, strength, intelligence and precision are the hallmarks of the linear actuator. All linear actuators can be used on a Profibus DP, CanOpen or DeviceNet fieldbus, whereby both parallel and serial control facilitate simultaneous starting.
In today’s world where the intensity of economic change is greater than ever, innovation has become not so much a sought-after key to exclusivity as a simple precondition of a company’s survival. Globalization, copying, volatile raw materials markets and added financial pressures are just a few of the factors which pose a multitude of risks. At the same time, the rapid pace of development in industry and science generates a steady stream of new innovation opportunities. For the machine building sector this means new challenges with regard to productivity, end product quality, plant availability and engineering flexibility. The urgent need for innovation remains unbroken in all these areas, with the design of the machine’s drive train frequently playing a vital role. Since precision and productivity are often constrained by the selected gearhead and motor
Always striving to offer the ideal gear reducer solution for customer application requirements, alpha is proud of its LP+/LPB+ Value Line series of gearheads. Its economic precision products are reliable and – thanks to a unique lubrication concept – maintenance-free for their entire service life. Focused on less demanding applications, these gear reducers offer outstanding efficiency with low tortional backlash. The LPB+ offers the option of adding an integrated geared pulley drive system. The belt pulley eliminates the need for a right angle gearbox, couplings and/or additional bearings - in turn, reducing cost, increasing performance, and reducing parts and engineering time for the system.
The alpha actuator system - an innovative alternative The alpha actuator system is based on a combination of several innovative elements, which only have the desired effect when united in this way: - Production and test engineering for rack-and-pinion units facilitate an unprecedented degree of precision - Innovative servo motor and transmission technology - Calculation, simulation, etc. of the complete system in tandem with other innovations (e.g. the type of connection between various system elements) The actuator system consists of a high-precision rack-and-pinion unit (positioning accuracy: < 12 microns) and a rotary actuator which moves the load on this unit.
As the first manufacturer to develop a hollow-shaft gearhead for maximum speeds, alpha now can supply the optimum right-angle gearhead for every application – be it worm, bevel or hypoid. The HG+ hollow-shaft gearhead made alpha the first manufacturer ever to develop a gearhead of this type capable of mastering even the most challenging servo applications. The HG+ is a low-backlash hypoid gearhead with a hollow-shaft, right angle design. Its numerous advantages include high torque and speed, gear ratios in a single stage, low noise combined with high efficiency and freedom from wear. The HG+ consequently offers a constant torsional backlash as well as perfect reversibility with all ratios. With innovative performance characteristics, a novel hollow-shaft flange output and impressive application flexibility, TK+ is a high-precision, multi-purpose product.
