|
|
Product ReleaseOEM Servo Motor Controller with CAN Print
 QuickSilver has added a CAN option to its smallest (2"/52mm x 2.5"/63mm) most cost effective servo motor controller . CAN can be configured for peer-to-peer, master or slave which allows the controllers to share I/O and registers with other CANopen enabled SilverDust controllers or3rd party CANopen devices (i.e. I/O blocks, encoders, PLCs...). For a multi-axis system, connect several MG-Cs, make one the master and let the others receive motion commands over CAN.This single axis, programmable controller is specially designed to servo 3rd party stepper motors creating a closed loop stepper system. It also includes serial communications (RS- 232, RS-485), and 7 I/O. The RS-232/RS-485 serial network runs independently in parallel toCAN for supervisory control from a host (i.e. PC, PLC, HMI..). The 7 bi-directional I/O, 12V-48V input power, and communications signals are accessed through the DB15HD port and can be separated using one of our popular breakouts (QCI-BOB,QCI-BO-B1, QCI-BO-B1A). For 24V I/O operations, QuickSilver recommends the QCI-BO-B52 breakout. Other MG-C Features: • 12-48V DC Input Power (UL CE) • 7 TTL, Bi-Directional I/O - For 24V use QCI-BO-B52 • 4 Analog Inputs  • Non-Volatile Memory - o ~3000 program lines • R2-232/485(ASCII, Modbus® RTU) • CAN • 100:1 Inertial Miss-Match • PVIATM Servo Loop • Point To Point Moves • Profile Moves • Electronic Gearing/Camming • Multiple Thread Programming ...
For more information please contact us.
NEMA 34 Servo Motor by QuickSilver $465 (500pc $372)
 QuickSilver Controls, Inc. expands its line of brushless AC servo motors with the QCI-A34M-1. This is the least expensive 34 frame motor designed to run on the SilverNugget N3 servo motor controller/driver. ...More >> Servo Motor - Simple 24V Power, Communication and I/O Breakout
OEM Servo Motor Controller with CAN by QuickSilver Controls
 QuickSilver has added a CAN option to its smallest (2"/52mm x 2.5"/63mm) most cost effective servo motor controller. CAN can be configured for peer-to-peer, master or slave which allows the controllers to share I/O and registers with other CANopen enabled SilverDust controllers or 3rd party CANopen devices (i.e. I/O blocks, encoders, PLCs...). For a multi-axis system, connect several MG-Cs, make one the master and let the others receive motion commands over CAN.
...More >>
QCI-A34L-1 NEMA 34 Servo Motor by QuickSilver Controls
 QuickSilver Controls, Inc. expands its line of servo motors with the QCI-A34L-1. The 34L-1 only requires 4.5A which means a single cable can be used for both motor and encoder signals and the servo motor can be driven from a small SilverDust D2 controller. ...More >>3D Solid Motor Models by QuickSilver Controls
 QuickSilver Controls now has solid models for its motors and controllers. ...More >>3D Solid Controller Models by QuickSilver Controls
 QuickSilver Controls now has solid models for its motors and controllers. These models allow the designer to easily drop our motors and motor controllers in into their application’s solid model. They are available in STEP format (.stp). 3D views which allow rotation and zoom are available in Acrobat 3D format. Go to our website to download the format of your choice. ...More >> Servo Motor Controller with DMX512x
 QuickSilver Controls adds the DMX512 serial protocol to its SilverDust™ line of servo motor controllers. This popular entertainment industry standard (ETSA E1.11-2004) allows a master show controller to broadcast a packet of information up to 44 times per second (250K baud) over an RS-485 line. The DMX frame contains 512 bytes or "Slots" of data to control such things as lighting dimmers, fog machines, and now QuickSilver’s servo motors. Each piece of equipment is pre-configured to only receive data from its Slot. Therefore, all the show elements are synchronized. Multiple DMX Slots can be “mapped” to multiple servo controller registers. Since the SilverDust is a programmable motor controller, the data can be used for anything. ...More >> OEM Servo Motor Controller/Driver Board by QuickSilver Controls
 QuickSilver Controls offers a Servo Controller, Motor and Cable for $795. For OEMs or those people who have to fit a powerful servo motor controller/driver into a small place, QuickSilver Controls offers its popular SilverDust servo controller/driver in a user mountable, board only option. The “board only” SilverDust IG (QCI-D2-IG-01) is a combined controller/driver which includes serial communications, 7 I/O, and 32K user program space but measures only 3”x2.75” (76mm x 70mm). The user is responsible for mounting the board and heat sinking the drivers allowing for a customizable package. ...More >>Servo Motor - 145 oz-in (1Nm) NEMA 23 Frame Servo Motor
 QuickSilver Controls, Inc. expands its current line of servo motors with the QCI-A23K-3. This NEMA 23 frame motor generates 145 oz-in (1.0Nm) continuous torque, 165 oz-in (1.1Nm) peak torque, and 58W peak mechanical power. The 23K-3 comes standard with an 8000 count/rev encoder and is available in both IP50 and IP65 (wash down) packages. When combined with QuickSilver’s line of easy to use servo controller/drivers, this motor creates a high torque servo control system for speeds up to 2000 RPM. ...More >>Application Story - Servo Controlled Rotary Knife Application
 QuickSilver Controls’ SilverDust servo controller/driver is now capable of doing rotary knife applications. Rotary knife systems are widely used to cut, seal or perforate material moving along a conveyor. A rotary knife system consists of a cylinder with a knife blade fastened along the longitudinal axis. As the cylinder rotates, it cuts the material passing underneath it. During the cut, the tangential knife velocity must match the linear speed of the material. During the rest of the revolution, the knife must either speed up or slow down to be ready for the next cut. ...More >> Motor Controller - Servo Motor Controller / Driver
 SilverDust IGF A Simple Servo Controller/Driver for NEMA 11, 17 and 23 High Torque, Direct Drive Servomotors QuickSilver Controls, San Dimas CA, releases a simple servo controller/driver for its line of NEMA 11, 17 and 23 frame high torque, direct drive servomotors. The QuickSilver IGF features a compact DIN rail mountable design, 7 TTL level I/O (optional 24V), RS-232/485 serial interface, ASCII/Modbus protocol, and enough memory for several thousand lines of programming. ...More >> Servo Amplifier - SilverDust IGF, A Simple Servo Controller/Driver
 For NEMA 11, 17 and 23 High Torque, Direct Drive Servomotors QuickSilver Controls releases a simple servo controller/driver for its line of NEMA 11, 17 and 23 frame servomotors. The IGF features a compact DIN mountable design, 7 TTL level I/O (optional 24V), RS-232/485 communications, and enough memory for several thousand lines of programming. Like the other SilverDust IG controller/drivers, the IGF comes with a built in regenerative braking circuit, single connector to motor, and an on/off switch. ...More >> Linear Servomotor from a Linear Step Motor
 QuickSilver Controls, Inc., known for its ability to servo rotary microstep motors now extends these capabilities to include servoing linear step motors. The QCI-L6 is a Linear Motor with full servo control which is ideal for high acceleration moves - up to 8.4G - which includes pick-and-place, wire bonding, semiconductor, parts inspection, and other high acceleration applications. The technology required to servo a rotary step motor is not that much different than that required to servo a linear step motor. Servoing a linear step motor retains all the advantages of servoing a rotary step motor. Servo control adds accuracy and repeatability, while eliminating the problems of resonance, stalling and excess heating. ...More >>QuickSilver's Introduces the M11-1 Its Smallest Servomotor Yet
 QuickSilver Controls, Inc. expands its current line of high-torque, direct-drive servomotors to include a NEMA 11 frame. With a face plate of only 1.1 inches and a length of 2 inches, the M11-1 is designed to fit in all those small places. The NEMA 11 frame motor generates 9 in-oz of continuous torque and comes with a 4000 count/rev encoder.
...More >>
QuickSilver's Newest Servo Controller Includes Ethernet and CAN
 QuickSilver Controls, Inc. responds to industry's demand for low cost network support with its newest single axis controller/driver. The SilverDust IG8 communication options include RS232, RS485, CAN and Ethernet. This multi-channel architecture allows for a network of field devices using CAN to work simultaneously with a supervisory network using RS232, RS485 or Ethernet.
...More >>
QuickSilver Makes Joystick Control Easy
 QuickSilver Controls, Inc., line of controller/drivers for servo control of NEMA 17, 23 and 34 frame stepmotors accommodates a simple analog joystick input to control position, velocity or torque. Joysticks are useful for augmenting complex motion control systems for such things as computerized microscopes and vision systems. On the fly, the controller can switch from joystick control to automated control. An example would be using the joystick to pan around a product, pressing the button at several “interesting” points. The controller would be able to memorize these points and move back to them latter for a more detailed inspection.
...More >>
QuickSilver Adds CAN to the SilverDust
 QuickSilver Controls, Inc., adds CAN bus to its SilverDust™ IGB servo motion controller/driver for servo control of NEMA 17 and 23 frame stepmotors. The CANopen compatible interface is fully isolated and supports up to 64 devices on the 1MB bus. The addition of CANopen enhances the motion controller’s unique ability to servo microstep motors by allowing one servo to modify the motion of another servo. CANopen may be used to interface to other CANopen products (Master or Slave) or as a “local” bus for peer-to-peer register sharing for such things as encoder position, velocity, torque and I/O. The motion controller’s serial port (RS232 or RS485) is still available for interface to a host such as a PLC, HMI or PC.
...More >>
QuickSilver Controls Offers Right Angle Motor Cable Adapters
 For those applications where you need to squeeze a NEMA 17 or NEMA 23 motor into a tight spot, QuickSilver Controls, Inc., now offers adapters for its 15 pin D shell motor connector (D15HD). The QCI-D15HD-R1 routes the cable towards the motor shaft and the QCI-D15HD-R2 routes the cable away from the shaft. Both adapters provide a height profile of 1 inch. Screws are included to secure the adapter to the motor. Both adapters are designed to handle the full horsepower of either a SilverNugget N2 or SilverDust D2 servo controller/driver including both motor and encoder feedback signals. For more details, see the technical document “QCI-TD049 D15HD Rt Angle Adapter - QCI-D15HD-R1 -R2” on QuickSilver’s website(www.QuickSilverControls.com).
...More >>
QuickSilver Controls Programmable Limit Switch added to Servo Controller  QuickSilver Controls, Inc., adds a Programmable Limit Switch (PLS) output to its SilverDust™ controller/driver for servo control of NEMA 17 and 23 frame microstep motors.
The PLS command can be configured to use any of the motion controller’s possible 23 I/O to change states (i.e. high to low or low to high) at more than 150 pre-defined trigger points. A modulo may be selected to repeat the cycle.
The controller compares the stepmotor position with the trigger position every 120 microseconds. When the trigger point is reached, the state of the I/O toggles automatically and the PLS command starts looking for the next trigger point.
Output triggering, trigger point values and number of trigger points may be changed dynamically even while the PLS command is running in the background. In factory automation, this could be used to change an output’s firing sequence for each part coming down the assembly line.
...More >>
QuickSilver Controls SilverDust Servo Controller Adds Open Loop Operation  San Dimas, CA - QuickSilver Controls Inc. has added open loop operation to its servo controller, the SilverDust. For years QuickSilver has produced servo controllers for microstep motors and now it has optimized the SilverDust to also operate a stepmotor in the traditional open loop configuration. Open loop operation is ideal for slower applications that do not require encoder feedback. SilverDust provides a powerful controller without the expense of an encoder and sophisticated cable. A savings of about $100 (list).
To make putting together open loop systems easier, QCI now sells its stepmotors and cabling for open loop operation.
For more details, see the datasheets on QuickSilver's website.
QuickSilver Controls manufacturers products to provide servo control for micro step motors. The SilverNugget and SilverDust are single axis, servo controller/driver modules designed to servo QuickSilver's line of NEMA 17, 23, and 34 step motors.
...More >>
QuickSilver Controls Offers Servo Control of NEMA 34 IP65 Stepmotors  QuickSilver Controls, Inc., know for its ability to servo microstep motors, now offers NEMA 34 IP65 stepmotors with encoders for wash down applications.
Based on QuickSilver's existing NEMA 34 frame stepmotors, this new line exceeds the IP65 standard. Two IP65 industrial, round connectors are used for encoder and motor signals. All motors come standard with a 16000 count/rev encoder. A shaft seal is included to extend the IP65 rating to the shaft.
Closed loop, servo control of these new NEMA 34 IP65 stepmotors is provided by the SilverNugget controller/driver.
...More >>
SilverDust IGB - Servo Controller/Driver for Microstep Motors with 16 I/O  QuickSilver Controls, Inc., known for its ability to servo microstep motors, released its most feature rich single axis controller/driver yet. The SilverDust IGB, part of the SilverLode controller family, is designed to servo, QuickSilver's high torque NEMA 17 and NEMA 23 frame I-Grade motor/encoders and includes breakouts for power, communications and I/O. Closed loop control (servo) of a stepmotor, provides all the accuracy of a traditional servomotor but with superior torque for applications up to a few thousand RPM and at a lower cost.
The IGB only uses a single cable for both motor and encoder signals. At 50', the cable has minimal voltage drop and excellent noise rejection. This combined with the IGB's new ability to upload encoder and motor information from the motor's on-board, non-volatile memory makes initialization as simple as plugging in the motor and pressing a button.
Other IGB Features:
...More >>
QuickSilver Controls Offers SilverDust IGB -Servo Controller/Driver for Microstep Motors with 16 I/O  QuickSilver Controls, Inc., known for its ability to servo microstep motors, releases its most feature rich single axis controller/driver yet. The SilverDust IGB, part of the SilverLode controller family, is designed to servo, QuickSilver's high torque NEMA 17 and NEMA 23 frame I-Grade motor/encoders and includes breakouts for power, communications and I/O. Closed loop control (servo) of a stepmotor, provides all the accuracy of a traditional servomotor but with superior torque for applications up to a few thousand RPM and at a lower cost.
The IGB only uses a single cable for both motor and encoder signals. At 50', the cable has minimal voltage drop and excellent noise rejection. This combined with the IGB's new ability to upload encoder and motor information from the motor's on-board, non-volatile memory makes initialization as simple as plugging in the motor and pressing a button.
...More >>
Washdown Products - IP65 NEMA 23 Frame Motor / Encoders  QuickSilver Controls fills the industry need for a wash down servo system with its new line of NEMA 23 IP65 motor/encoders. Based on QuickSilver’s existing 23 frame motors, this new line exceeds the IP65 standard. Both the motor and encoder signals route through the single, round, connector. A single cable connects the IP65 motors to QuickSilver’s existing line of servo controller/drivers ...More >> QuickSilver’s New 380 in-oz 23 Frame Motor is Ideal for Driving Large Flywheel Loads without Additional Gearing  QuickSilver Controls, Inc., adds the 23T-7 motor/encoder to its line. The new NEMA 23 frame motor generates 380 in-oz of torque and comes with an 8000 count/rev encoder. When combined with QuickSilver’s line of servo controller/drivers, this micro step motor creates a high torque servo control system at speeds up to 1000RPM.With QCI’s ability to handle inertial miss-matches of 100x1. The 23T is miserly on power, requiring the controller to draw only 3 amps from the 12V to 48V power supply. A single cable is required to connect the motor/encoder to the controller/driver. See the QuickSilver website for a datasheet on the QCI-A23T-7-A-01 .... ...More >> QuickSilver Controls' 34 Frame I-Grade System Offers Servo Control  QuickSilver Controls, Inc., offers servo control of its NEMA 34 frame step motors. The system includes QuickSilver’s I-Grade SilverNugget N3 Controller/Driver and one of six 34 frame step motor with attached encoders.The 34 frame I-Grade motor/encoders range in torque from 500 in-oz to over 3200 in-oz and all have 16000 count/rev encoders. The I-Grade System easily handles inertial miss-matches of 100x1 which makes it ideal for direct driving large loads in applications such as labeling, packaging and web handling. Product Datasheets are available on the company Web site, product information requests and application questions are encouraged through the link below.... ...More >> QuickSilver Controls Offers a New Compact SilverDust™ Servo Controller/Driver For 17 and 23 Frame Step Motors  The SilverDust is a highly compact motion controller and driver for running micro step NEMA 23 and smaller motors closed loop.So how does a “Step Motor” become a servo? “Step motors” are really classified as high pole count AC synchronous motors. QCI is able to commutate a high pole motor (step motor) to form an AC brushless motor. QCI uses encoder based position feedback to determine the position error and dynamically varies the motor torque to achieve the sought position. The result of this methodology is a high torque servomotor. As with other servomotors, when the load is removed the motor does not need to generate torque. The motor current decreases, thus reducing the power consumption and heat generated. SilverNugget provides the engineer flexibility to program appli... ...More >> QuickSilver Controls Offers the SilverNugget I-Grade Controller/Driver and Motor/Encoder  QuickSilver provides servo control of a 17 or 23 frame micro step motor utilizing a single cable for both motor and encoder signals. 34 frame motors have a second cable to handle the high current motor signals. SilverNugget I-Grade controller/driver and the I-Grade motor/encoders use standard DB connectors, which allows for inexpensive and reliable cables. The system is ideal for dusty environments and meets IP50 standards. The I-Grade SilverNuggets come with QuickSilver’s standard DB15 data connector for the 7 I/O and communications signals. This ensures compatibility with QuickSilver breakout and I/O accessories. The I-Grade SilverNugget, motor/encoder and cable are designed for low EMI emission and excellent signal integrity. See the QuickSilver website for datasheet... ...More >> QuickSilver Controls' SilverNugget N2 is the Latest in Servo Controller and Driver Products  The SilverNugget N2 is a highly compact motion controller and amplifier for driving high pole count micro step NEMA 17 and 23 frame motors. With the addition of a high-resolution encoder and a bipolar micro step motor, the SilverNugget provides a high performance rotary positioning system. The SilverNugget has two integrated cables for interfacing with the primary encoder as well as the micro step motor.QuickSilver Controls manufacturers products to provide servo control for micro step motors. The SilverNugget and SilverDust are single axis, servo controller/driver modules designed to servo QuickSilver's line of NEMA 17, 23, and 34 step motors. Some product UL/CE marked in both IP50 and IP65 ratings.... ...More >> |
|
|
|